Skip to main content

Nexo DTDAMP4X0.7

Nexo DTDAMP4X0.7

£1,219.00

Out of stock



The DTDAMP range is composed of two models of four channel amplifiers housed in a 1U rack and weighting only 7.5 Kg. The DTD Controller offers a very efficicent solution for processing most of the Nexo Speakers, from the ID series to our world famous PS15.


Category: Brand:

Overview

The DTDAMP range is composed of two models of four channel amplifiers housed in a 1U rack and weighting only 7.5 Kg. The DTD Controller offers a very efficicent solution for processing most of the Nexo Speakers, from the ID series to our world famous PS15. When used with a DTDAMP you are sure to get all the necessary power for your NEXO speakers, while this combo offers both a coherent look and ease of use. A pair of DTD + DTDAMP will weigh together less than 10 Kg, while being able to process and power system composed, for example, of 2 x NEXO Speakers + 2 x NEXO subs. This performance is due to the use of high-density and highly integrated components together with high-efficiency design (smaller heatsinks) for power supply/power amplifier parts. The DTDAMP offers all the sensor and protection that are mandatory for a professional touring amplifier, such as mains over/under voltage, Over-voltage or DC output on each channel, short circuit etc. The variable speed cooling system will assure a quiet and cool amplifier while the front to back cooling system ensure compatibility inside racks where both DTDAMP and our high-end NXAMP are used together in large installations. Once your NEXO Speakers are selected in your DTD Controller, you can use your DTD +DTDAMP system in most situations without any further adjustments to the settings. When used with the NEXO DTD controller the DTDAMP is the perfect solution for “Dry” hire or where the user has a limited knowledge but still allowing the best possible result from the Nexo speaker system.

KEY FEATURES

  • Two models of high-power, lightweight four channel amplifiers
  • Perfect match for the NEXO speakers supported by the DTD Controller
  • High-efficiency Switch Mode power supply and Amplifier channel design
  • Channels can be independently bridged two by two
  • Four Inputs on XLR connectors and four Outputs on SP-4 connectors
  • Extensive protection (Mains over/ undervoltage, temperature, DC outputs, current and voltage peak limiters, variable speed cooling system)

Product Specifications

SPECIFICATIONS

Number of channels 4 x amplifiers channel, 2 by 2 bridgeable
Max. output voltage (no Load) 4 x 85 Volts
Max. output power (4 x 8 Ohms) 4 x 360 Watts
Max. output power (4 x 4 Ohms) 4 x 700 Watts
Max. output power (2 bridge x 8 Ohms) 2 x 1400 watts
Frequency response +/- 0.5 dB from 20 Hz to 20 kHz
Input impedance 10 kOhms
Input sensitivity +5 dBU
Nominal Gain 32 dB
Dynamic Range (A-weighted) > 110 dB
THD+N Typical 0.01%

FEATURES

Analog audio inputs 4 x balanced analog inputs on XLR
Power outputs 4 x SP4 outputs
Link switch To use same XLR input for 2 x adjacent channels
Mains sockets IEC C14 Inlet with secure lock
Switch and knobs Mains On/Off switch and volume control knob per channel
View meters x LEDs (signal / -18 dB / -6 dB / Peak) per channel
Amplifier status Amp Ready and Temperature indicator per channels pairs
Mains voltage Factory set for 120 volts of 230 volts mains operation
Power consumption (Idle) 65 Watts
Power consumption 1/8 max. / 4 Ohms 580 Watts
Power consumption 1/4 max. / 4 Ohms 1100 Watts
Dimensions (W x H x D) 480 (W) x 44 (H) x 370 (D) mm, 19 inches / 1U
Weight 7.5 kg
Operating temperature range 0°C – 45 °C
CE conformity 2006/95/CE (Low voltage) 2004/108/CE (EMC) 2002/95/CE (RoHS)
Electrical safety certification CSA, CB, EN60065
EMC certification EN55103-1 / EN55103-2 / FCC

    Product Details


    X